Choose a free accessory with a multifunction tester.Shop Now
*** Please note that this offer is available for a limited time only and is subject to availability or while stocks last. ***
The Amprobe ProInstall-75-UK MFT with EV-520-UK Test Adapter Kit includes the following products:
Please see the descriptions below for further information regarding Amprobe’s multifunction installation tester and test adapter kit.
The Amprobe ProInstall-75-UK Multifunction Installation Tester is optimised for industrial, commercial and domestic environments. It can be used to test fixed wiring installations in these areas. As such it includes a comprehensive array of tests ensuring that it is able to verify the safety and functionality of electrical installations in accordance with IEC 60364, HD 384 requirements and BS7671 18th Edition wiring regulations.
The Amprobe ProInstall-75-UK Multifunction Installation Tester is able to check the following electrical parameters:
The Amprobe ProInstall-75-UK Multifunction Installation Tester also includes an advanced loop test that prevents RCDs from tripping, a fast high-current loop test, and selectable voltage measurements between L-N, L-PE and N-PE.
This instrument can be tailored to suit a variety of applications and, to this end, includes a number of insulation test voltages and a variable RCD current mode for customising the Amprobe ProInstall-75-UK Multifunction Installation Tester to suit various applications.
Measurements are indicated on the Amprobe ProInstall-75-UK Multifunction Installation Tester’s large display with a wide viewing angle. It is possible to view resistance measurements to a resolution of 0.01Ω. Additionally, the user is able to view mains voltage and frequency measurements simultaneously.
Furthermore, the Amprobe ProInstall-75-UK Multifunction Installation Tester will issue a PASS/ FAIL indication for the results of RCD tests, ensuring that the user can be certain of his/her readings.
Also adding to the certainty and, therefore, reliability and accuracy of the Amprobe ProInstall-75-UK Multifunction Installation Tester is the included zero adapter, which compensates for test leads, and the Auto-Null function, which subtracts test lead resistance from readings. Subtracted test lead resistance is stored in the Amprobe ProInstall-75-UK Multifunction Installation Tester’s memory even after it has been switched off.
In addition to a zero adapter, the Amprobe ProInstall-75-UK Multifunction Installation Tester is supplied with slim reach probes allowing the user to check installations in difficult-to-access areas. Furthermore, this instrument is supplied with a padded neck strap facilitating hands-free operation. The Amprobe ProInstall-75-UK Multifunction Installation Tester is compact, ergonomic and lightweight ensuring that it is easy to carry and therefore suitable for prolonged periods of testing.
The Amprobe ProInstall-75-UK Multifunction Installation Tester also features easy-to-operate controls allowing the user to select the required measurement function simply and swiftly. The user can select the required safety voltage level (50V or 25V) via this simple operating system, allowing him/her to tailor the Amprobe ProInstall-75-UK Multifunction Installation Tester to the environment.
In addition to selectable safety voltages, the Amprobe ProInstall-75-UK Multifunction Installation Tester includes a number of features designed to protect both the instrument and the user, including:
The Amprobe ProInstall-75-UK Multifunction Installation Tester is a sophisticated, small and safe multifunction tester optimised for checking the safety of industrial, commercial and domestic fixed wiring electrical installations in accordance with local regulations.
The Amprobe EV-520-UK Test Adapter Kit is optimised for use in the UK and as such includes the following equipment:
The Amprobe EV-520-UK Test Adapter Kit is optimised for checking the safety and functionality of UK electric vehicle charging stations (mode 3 for AC charging), as well as troubleshooting UK EV charging stations (mode 3 for AC charging). It can be used with Amprobe (and selected Fluke) multifunction installation testers and scope meters/ oscilloscopes in order to check and/or troubleshoot UK EV charging stations. To this end, it includes L1, L2, L3, N and PE measuring terminals which facilitate a connection to the user’s test instrument, such as the above Amprobe ProInstall-75-UK Multifunction Installation Tester.
The Amprobe EV-520-UK Test Adapter Kit is able to verify the safety and functionality of charging stations in accordance with IEC/EN 61851-1 and IEC/HD 60364-7-722 whilst simulating the presence of an electric vehicle.
This kit includes a type 2 EV connector and can be used to simulate CP error E and PE errors (earth fault). It is also capable of simulating various charging states using the Control Pilot (CP) State ‘Vehicle Simulation’ rotary switch. Moreover, the Amprobe EV-520-UK Test Adapter also includes a Proximity Pilot (PP) State ‘Cable Simulation’ rotary switch for mimicking the various current capabilities of charging cables.
Further to this, the Amprobe EV-520-UK Test Adapter includes a UK mains socket for checking the functionality and counting of an electric power meter via the connection of an external load. It also features CP terminals for checking the communication between the adapter (acting in the role of an electric vehicle) and the charging station.
In addition to these testing/ simulation capabilities, the Amprobe EV-520-UK Test Adapter also includes a PE Pre-test safety feature that can be used to test for the presence of dangerous voltage against earth. It also includes three LED lamps for separate phase indication allowing the user to identify the presence of voltage easily.
Finally, as the Amprobe EV-520-UK Test Adapter is optimised for verifying the safety and functionality of electric vehicle charging stations, which are often found outside, it features an IP54 protection rating, ensuring that it is protected against dust and water splashes.
The Amprobe EV-520-UK Test Adapter Kit is a comprehensive test kit that is ideal for expanding the capabilities and scope-for-use of the above Amprobe ProInstall-75-UK Multifunction Installation Tester.
Please find below the technical specifications for the products included in this offer.
|Size||10cm (L) x 25cm (W) x 12.5cm (H)|
|Weight (with Batteries)||1.3kg|
|Battery||6 x AA. Alkaline supplied. Usable with 1.2V NiCd or NiMH batteries (not included)|
|Battery Life (Typical)||200 hours idling|
|Fuse||T3.15 A, 500 V, 1.5 kA 6.3 x 32 mm (PN 2030852)|
|Operating Temperature||-10 to 40°C|
|Storage Temperature||-10 to 60°C indefinitely (to -40°C for 100 hours)|
|Relative Humidity||Non-condensing 80%: 10 to 35°C
70%: 35 to 40°C
|Operating Altitude||0 to 2000m|
|Shock, Vibration||Vibration to Class 3 per Mil-Prf-28800F 1 meter drop test, six sides, oak floor|
|EMC||Complies with EN61326-1: 2006|
|Safety||Complies with EN61010-1 Ed 2.0 (2001-02), UL61010, ANSI/ ISA
-s82.02.01 2000 and CAN/CSA c22.2 No.1010 2nd edition Overvoltage
Category III (CAT III), 500 V Measurement Category III is for
measurements performed in the building installation. CAT IV, 300V.
Examples are distribution panels, circuit breakers, wiring and cabling.
Performance EN61557-1, EN61557-2, EN61557-3, EN61557-4, EN61557-5,
EN61557-6, EN61557-7 Second edition. EN61557-10 First edition.
|Maximum Voltage Between Any Terminal and Earth Ground||500V|
|Surge Protection||6 kV peak per EN 61010-1 Ed. 2.0 (2001-02)|
|AC Voltage Measurement (V)|
|Display Range||Resolution||Accuracy 50Hz to 60Hz||Input Impedance||Overload Protection|
|0 to 500V||0.1V||0.8% + 3||3.3MΩ||600V RMS|
|Continuity Testing (RLo)|
|Display Range (Autoranging)||Resolution||Open Circuit Voltage||Accuracy||Range RLo||Test Current|
|0 to 20Ω||0.01Ω||>4V||±(1.5% + 3 digits)||7.5||210mA|
|200Ω||0.1Ω||>4V||±(1.5% + 3 digits)||240||20mA|
|2000Ω||1Ω||>4V||±(1.5% + 3 digits)||2000||2mA|
|Test Probe Zeroing||Press the (zero) button to zero the test probe. Can subtract up to 2 Ω of lead resistance. Error message for >2 Ω.|
|Live Circuit Detection||Inhibits test if terminal voltage >10 V ac detected prior to initiation of test.|
|Insulation Resistance Measurements (Riso)|
|Test Voltages||250, 500, 1000V|
|Accuracy of Test Voltage (At Rated Test Current)||+10%, -0%|
|Test Voltage||Insulation Resistance Range||Resolution||Test Current||Accuracy|
|50V||10 kΩ to 50 MΩ||0.01 MΩ||1mA @ 50kΩ||±(3 % + 3 digits)|
|100V||100 kΩ to 20 MΩ||0.01 MΩ||1mA @ 100kΩ||±(3 % + 3 digits)|
|20 MΩ to 100 MΩ||0.1 MΩ||±(3 % + 3 digits)|
|250V||10 kΩ to 20 MΩ||0.01 MΩ||1mA @ 250kΩ||±(1.5% + 3 digits)|
|20 MΩ to 200 MΩ||0.1 MΩ||±(1.5% + 3 digits)|
|500V||10 kΩ to 20 MΩ||0.01 MΩ||1mA @ 500kΩ||±(1.5% + 3 digits)|
|20 MΩ to 200 MΩ||0.1 MΩ||±(1.5% + 3 digits)|
|200 MΩ to 500 MΩ||1 MΩ||±10%|
|1000V||100 kΩ to 200 MΩ||0.01 MΩ||1mA @ 1MΩ||±(1.5% + 3 digits)|
|200 MΩ to 1000 MΩ||1 MΩ||±10%|
|Auto Discharge||Discharge time constant <0.5 second for C=1μF or less|
|Live Circuit Detection||Inhibits test if terminal voltage >30V prior to initiation of test|
|Maximum Capacitive Load||Operable with up to the 5μF load|
|Loop and Line Impedance (Zl), No Trip and Hi Current Modes RCD/FI|
|Mains Input Voltage Range||100 to 500V AC (50/60Hz)|
|Input Connection (Soft Key Selection)||Loop Impedance: Phase to Earth
Line Impedance: Phase to Neutral
|Limit on Consecutive Tests||Automatic shutdown when internal components are too hot.
There is also a thermal shutdown for RCD tests
|Maximum Test Current at 400V||20A sinusoidal for 10ms|
|Maximum Test Current at 230V||12A sinusoidal for 10ms|
|10Ω||0.001Ω||Hi Current Ω: ±2% +15 digits)|
No Trip Mode: ±3% + 6 digits
Hi Current Mode: ±(2% + 4 digits)
|200Ω||0.1Ω||No-Trip Mode: ±(3%)
Hi Current Mode: ±2%
|Notes * Valid for resistance of neutral circuit <20 Ω and up to a system phase angle of 30°. Test leads must be zeroed before testing.
** Valid for mains voltage >200 V.
|Prospective Earth Fault Current Test (PSCI/Ik)|
|Resolution and Units||Resolution||Units|
|IK < 1000A||1A|
|IK > 1000A||0.1kA|
|Computation||Prospective Earth Fault Current (PEFC/IK) or Prospective Short Circuit Current (PSC/IK) determined by dividing
measured mains voltage by measured loop (L-PE) resistance or line (L-N) resistance, respectively.
|Range||0 to 10 kA or 0 to 50 kA (See Power-On Options earlier in this manual)|
|Accuracy||Determined by accuracy of loop resistance and mains voltage measurements.|
|Types Tested||AC1, AC, A4, A, G2, S3, G, S|
|AC||The waveform is a sinewave starting at zero crossing, polarity determined by phase selection (0° phase starts with low to high zero
crossing, 180° phase starts with high to low zero crossing). The magnitude of the test current is IΔn x Multiplier for all tests.
|A||The waveform is a half wave rectified sinewave starting at zero, polarity determined by phase selection (0° phase starts with low to
high zero crossing,180° phase starts with high to low zero crossing). The magnitude of the test current is 2.0 x IΔn (rms) x Multiplier
for all tests for IΔn = 0.01A. The magnitude of the test current is 1.4 x IΔn (rms) x Multiplier for all tests for all other IΔn ratings.
|B||Smooth DC current according to EN61557-6 Annex A|
|Tripping Speed Test (ΔT)|
|Current settings**||Multiplier||Current Accuracy|
|10–30–100–300–500–1000 mA -VAR||x 1/2||+0 %, -10 % of test current|
|10–30–100–300–500–1000 mA -VAR||x 1||+10 %, -0 %|
|10–30–100 mA||x 5||+10 %, -0 %|
|Note, 1 1000 mA type AC only. 700 mA maximum type A in VAR mode, not available for type B.|
|Current Multiplier||*RCD type||Measurement Range||Trip Time Accuracy|
|x 1/2||G||310 ms||2000 ms||±(1 % Reading + 1 ms)|
|x 1/2||S||510 ms||2000 ms||±(1 % Reading + 1 ms)|
|x 1||G||310 ms||310 ms||±(1 % Reading + 1 ms)|
|x 1||S||510 ms||510 ms||±(1 % Reading + 1 ms)|
|x 5||G||50 ms||50 ms||±(1 % Reading + 1 ms)|
|x 5||S||160 ms||160 ms||±(1 % Reading + 1 ms)|
|Notes||*G – General, no delay|
|*S – Time delay|
|Maximum Trip Time|
|The RCD √ symbol switches on when testing the RCD trip time if the trip time meets the following conditions.|
|RCD||I Δ N||Trip Time Limits|
|AC G, A, B||x 1||Less than 300 ms|
|AC, G - S type, A - S type, B - type||x 1||Between 130 ms and 500 ms|
|AC G, A, B||x 5||Less than 40 ms|
|AC, G - S type, A - S type, B - type||x 5||Between 50 ms and 150 ms|
|RCD/FI-Tripping Current Measurement/Ramp Test (IΔN)|
|Current Range||Step Size||Dwell Time||Measurement Accuracy|
|Type G||Type S|
|30 % to 110 % of RCD rated current1||10 % of IΔN 2||300 ms/step||500 ms/step||±5 %|
1 30 % to 150 % for Type A IΔN >10 mA
30 % to 210 % for Type A IΔN = 10 mA
20 % to 210 % for Type B
Specified trip current ranges (EN 61008-1):
50 % to 100 % for Type AC
35 % to 140 % for Type A (>10 mA)
35 % to 200 % for Type A (≤10 mA)
50 % to 200 % for Type B 2 5% for Type B
|Phase Sequence Indication|
|Icon||icon Phase Sequence indicator is active|
|Display of Phase Sequence||Displays “1-2-3” in digital display field for correct sequence. Displays “3-2-1” for incorrect phase. Dashes in place of a number indicate a valid determination could not be made.|
|Mains Input Voltage Range (phase-tophase)||100 to 500 V|
|PE Pre-Test||Yes, with touch electrode|
|PP simulation||open, 13 A, 20 A, 32 A, 63 A|
|CP states||A, B, C, D|
|CP Error “E”||on/off|
|PE Error (Earth fault)||on/off|
|Outputs (for test purpose only)|
|Measuring terminal L1, L2, L3, N and PE||Max. 250/430 V, CAT II 300 V, max. 10 A|
|Mains socket||Max. 250 V, CAT II 300 V, allowed current max. 10 A|
|CP Signal output terminals||PWM communication protocol, approx. max. ±12 V|
|Input voltage||Up to 250 V (single phase system) / up to 430 V (three phase system), 50/60 Hz, max 10 A|
|EV Connector (EVC-20)||AC charging mode 3, suitable to IEC 62196-2 type 2 socket outlet or fixed cable with vehicle connector (type 2, 7P three-phase)|
|EV Connector (EVC-13) OPTIONAL||AC charging mode 3, suitable to IEC 62196-2 type 1 or SAE J1772 with vehicle connector (type 1, 5P single-phase)|
|Mains outlet protection||Fuse T 10 A/250 V, 5×20 mm|
|Dimensions (W × H × L)||110 × 45 × 220 mm (length without connection cable and connector)|
|Weight||Approx. 1 kg (Adapter EVA-500-x + EC-connector EVC-20)|
|IP protection class||IP54|
|CE directive||Low Voltage Directive LVD 2014/35/EU|
|Working temperature range||0 ... +40 °C|
|Storage temperature range||-10 ... +50 °C|
|Reference humidity range||10 ... 60 % relative humidity w/o condensation|
|Working humidity range||10 ... 85 % relative humidity w/o condensation|
|Measurement category||CAT II 300 V|
|Altitude above sea level||2000 m max.|
We'd really appreciate it if you'd review this product
Why not leave a review of this product? Reviews help us improve our service for customers looking for a product to make a decision.No reviews have been found