Choose a free accessory with a multifunction tester.Shop Now
Introducing Beha-Amprobe's ProInstall 75-UK, a multifunction electrical installation tester made for those who work in demanding environments.
Suitable for use in domestic, commercial and industrial electrical applications, the ProInstall 75-UK is also ideal for ensuring that fixed wiring is installed and compliant with IEC 60364 and HD 384 standards.
The Beha-Amprobe ProInstall 75-UK can perform all of the following measurement procedures:
Whether it's propped on a surface or around your neck on a strap, the Beha-Amprobe 75-UK makes it easy to test in any electrical installation.
This multifunction tester comes with a wide variety of benefits including:
Work confidently and with peace of mind thanks to the Beha-Amprobe 75-UK's built-in safety capabilities.
Inside your pack you'll find:
|Size||10cm (L) x 25cm (W) x 12.5cm (H)|
|Weight (with Batteries)||1.3kg|
|Battery||6 x AA. Alkaline supplied. Usable with 1.2V NiCd or NiMH batteries (not included)|
|Battery Life (Typical)||200 hours idling|
|Fuse||T3.15 A, 500 V, 1.5 kA 6.3 x 32 mm (PN 2030852)|
|Operating Temperature||-10 to 40°C|
|Storage Temperature||-10 to 60°C indefininitely (to -40°C for 100 hours)|
|Relative Humidity||Non-condensing 80%: 10 to 35°C
70%: 35 to 40°C
|Operating Altitude||0 to 2000m|
|Shock, Vibration||Vibration to Class 3 per Mil-Prf-28800F 1 meter drop test, six sides, oak floor|
|EMC||Complies with EN61326-1: 2006|
|Safety||Complies with EN61010-1 Ed 2.0 (2001-02), UL61010, ANSI/ ISA
-s82.02.01 2000 and CAN/CSA c22.2 No.1010 2nd edition Overvoltage
Category III (CAT III), 500 V Measurement Category III is for
measurements performed in the building installation. CAT IV, 300V.
Examples are distribution panels, circuit breakers, wiring and cabling.
Performance EN61557-1, EN61557-2, EN61557-3, EN61557-4, EN61557-5,
EN61557-6, EN61557-7 Second edition. EN61557-10 First edition.
|Maximum Voltage Between Any Terminal and Earth Ground||500V|
|Surge Protection||6 kV peak per EN 61010-1 Ed. 2.0 (2001-02)|
|AC Voltage Measurement (V)|
|Display Range||Resolution||Accuracy 50Hz to 60Hz||Input Impedance||Overload Protection|
|0 to 500V||0.1V||0.8% + 3||3.3MΩ||600V RMS|
|Continuity Testing (RLo)|
|Display Range (Autoranging)||Resolution||Open Circuit Voltage||Accuracy||Range RLo||Test Current|
|0 to 20Ω||0.01Ω||>4V||±(1.5% + 3 digits)||7.5||210mA|
|200Ω||0.1Ω||>4V||±(1.5% + 3 digits)||35||100mA|
|2000Ω||1Ω||>4V||±(1.5% + 3 digits)||240||20mA|
|Test Probe Zeroing||Press the (zero) button to zero the test probe. Can subtract up to 2 Ω of lead resistance. Error message for >2 Ω.|
|Live Circuit Detection||Inhibits test if terminal voltage >10 V ac detected prior to initiation of test.|
|Insulation Resistance Measurements (Riso)|
|Test Voltages||250, 500, 1000V|
|Accuracy of Test Voltage (At Rated Test Current)||+10%, -0%|
|Test Voltage||Insulation Resistance Range||Resolution||Test Current||Accuracy|
|50V||10 kΩ to 50 MΩ||0.01 MΩ||1mA @ 50kΩ||±(3 % + 3 digits)|
|100V||100 kΩ to 20 MΩ||0.01 MΩ||1mA @ 100kΩ||±(3 % + 3 digits)|
|20 MΩ to 100 MΩ||0.1 MΩ||±(3 % + 3 digits)|
|250V||10 kΩ to 20 MΩ||0.01 MΩ||1mA @ 250kΩ||±(1.5% + 3 digits)|
|20 MΩ to 200 MΩ||0.1 MΩ||±(1.5% + 3 digits)|
|500V||10 kΩ to 20 MΩ||0.01 MΩ||1mA @ 500kΩ||±(1.5% + 3 digits)|
|20 MΩ to 200 MΩ||0.1 MΩ||±(1.5% + 3 digits)|
|200 MΩ to 500 MΩ||1 MΩ||±10%|
|1000V||100 kΩ to 200 MΩ||0.01 MΩ||1mA @ 1MΩ||±(1.5% + 3 digits)|
|200 MΩ to 1000 MΩ||1 MΩ||±10%|
|Auto Discharge||Discharge time constant <0.5 second for C=1μF or less|
|Live Circuit Detection||Inhibits test if terminal voltage >30V prior to initiation of test|
|Maximum Capacitive Load||Operable with up to the 5μF load|
|Loop and Line Impedance (Zl), No Trip and Hi Current Modes RCD/FI|
|Mains Input Voltage Range||100 to 500V AC (50/60Hz)|
|Input Connection (Soft Key Selection)||Loop Impedance: Phase to Earth
Line Impedance: Phase to Neutral
|Limit on Consecutive Tests||Automatic shutdown when internal components are too hot.
There is also a thermal shutdown for RCD tests
|Maximum Test Current at 400V||20A sinusoidal for 10ms|
|Maximum Test Current at 230V||12A sinusoidal for 10ms|
|10Ω||0.001Ω||Hi Current Ω: ±2% +15 digits)
No Trip Mode: ±3% + 6 digits
|20Ω||0.01Ω||Hi Current Mode: ±(2% + 4 digits)|
|200Ω||0.1Ω||No-Trip Mode: ±(3%)
Hi Current Mode: ±2%
|Notes * Valid for resistance of neutral circuit <20 Ω and up to a system phase angle of 30°. Test leads must be zeroed before testing.
** Valid for mains voltage >200 V.
|Prospective Earth Fault Current Test (PSCI/Ik)|
|Resolution and Units||Resolution||Units|
|IK < 1000A||1A|
|IK > 1000A||0.1kA|
|Computation||Prospective Earth Fault Current (PEFC/IK) or Prospective Short Circuit Current (PSC/IK) determined by dividing
measured mains voltage by measured loop (L-PE) resistance or line (L-N) resistance, respectively.
|Range||0 to 10 kA or 0 to 50 kA (See Power-On Options earlier in this manual)|
|Accuracy||Determined by accuracy of loop resistance and mains voltage measurements.|
|Types Tested||AC1, AC, A4, A, G2, S3, G, S|
|AC||The waveform is a sinewave starting at zero crossing, polarity determined by phase selection (0° phase starts with low to high zero
crossing, 180° phase starts with high to low zero crossing). The magnitude of the test current is IΔn x Multiplier for all tests.
|A||The waveform is a half wave rectified sinewave starting at zero, polarity determined by phase selection (0° phase starts with low to
high zero crossing,180° phase starts with high to low zero crossing). The magnitude of the test current is 2.0 x IΔn (rms) x Multiplier
for all tests for IΔn = 0.01A. The magnitude of the test current is 1.4 x IΔn (rms) x Multiplier for all tests for all other IΔn ratings.
|B||Smooth DC current according to EN61557-6 Annex A|
We'd really appreciate it if you'd review this product
Why not leave a review of this product? Reviews help us improve our service for customers looking for a product to make a decision.No reviews have been found
Do you have a question or found it cheaper? Contact us