The TREND Networks NaviTEK III is a handheld network tester for troubleshooting copper, fibre and Wi-Fi networks. It provides network and port identification, cable and physical-layer diagnostics, PoE/PoE+ testing, VLAN discovery, IP information, connected device discovery and Wi-Fi analysis. The tester supports RJ45 and SFP connections, Wi-Fi 5/6/6E/7, multi-Gig speed detection and has a colour touchscreen.
NaviTEK III can identify issues across cabling, network ports, PoE, fibre links, VLANs, IP configuration, Wi-Fi infrastructure and connected devices. Test results can be synchronised, and reports shared via TREND AnyWARE Cloud connectivity, while NetMap device discovery, wire mapping with length and distance-to-fault measurement, access point details and channel mapping provide additional network diagnostics.
See the individual details below for the complete contents of each version.
*SFP modules not included. User-supplied SFPs can be used.
Automatically adds to your basket when the total exceeds £500+ (ex VAT). Limited Stock. More details here.
| Copper Cable Testing Functions | |||||||||||||||||||||||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Cable Testing | Live wiremap, TDR distance to open/short, 4-pair, 2-pair, 1-pair selectable, UTP/STP, allows crossover cable, 568A/568B/USOC colour code selectable Supports 12 wiremap remotes. |
||||||||||||||||||||||||||||||||||||||||
| Length Measurement | 0.3-450 m / 1-1476 ft. on 24 AWG / 0.2 mm2 or larger conductors 0.3-300 m / 1-984 ft. on 26 AWG / 0.13 mm2 conductors Display resolution: 0.1 m / 0.5 ft NVP range: 59-89% |
||||||||||||||||||||||||||||||||||||||||
| Length/TDR Accuracy | ±5% of cable length, ±0.5 m (1.5 ft) | ||||||||||||||||||||||||||||||||||||||||
| Input Protection | NaviTEK III handset: ≤60V Voltage warning when > 2 V detected Wiremap remotes: ≤10V DO NOT CONNECT TO PoE CIRCUITS |
||||||||||||||||||||||||||||||||||||||||
| Cable Tracing Tone Generator | Selectable analog/digital tone Selectable digital tone output: 129, 240, 455 kHz, compatible with most digital tracing probes Output voltage: ~5V peak-to-peak Output pins: 1/2, 3/6, 4/5, 7/8, 1, 2, 3, 4, 5, 6, 7, 8, all |
||||||||||||||||||||||||||||||||||||||||
| Power over Ethernet Classification | Automatic PoE classification: Type 1 to 4, Class 0 to 8 | ||||||||||||||||||||||||||||||||||||||||
| PoE Load Test Minimum Watts/Volts to Pass |
IEEE 802.3 af/at/bt compliant User-selectable high-power or low-power test mode
|
||||||||||||||||||||||||||||||||||||||||
| Fibre Optic Cable Testing Functions | |||||||||||||||||||||||||||||||||||||||||
| Continuity | Visual Fault Locator, 650 nm, 1 mW max Continuous or flash mode (1 second) 2.5mm connector for SC/ST/FC connectors and 1.25mm adapter for LC connectors. |
||||||||||||||||||||||||||||||||||||||||
| Length Measurement | SFP loopback length test 0-20 km / 0-12.5 miles (depending on SFP module). Display resolution: 1 m / 3.28 ft IoR (Index of Refraction) range: 1.30-1.55 |
||||||||||||||||||||||||||||||||||||||||
| Live Power Meter | Displays received power (dBm) from SFP modules that support diagnostic functions | ||||||||||||||||||||||||||||||||||||||||
| SFP Information | Displays brand, part number, wavelength, Rx power, Tx power and temperature of SFP modules that support diagnostic functions | ||||||||||||||||||||||||||||||||||||||||
| Fibre Connector Inspection | Supports TREND USB fibre microscopes Pass/Fail testing to IEC 61300-3-35 |
||||||||||||||||||||||||||||||||||||||||
| Network Test Functions | |||||||||||||||||||||||||||||||||||||||||
| Link Speed | RJ45: Connect to network at 10, 100 Mb/s, 1 Gb/s for diagnostic tests Manual or auto-negotiation SFP: Connect to network at 1Gb/s for diagnostic tests |
||||||||||||||||||||||||||||||||||||||||
| Port Speed Detection | RJ45: 10, 100 Mb/s, 1, 2.5, 5, 10 Gb/s link pulse identification | ||||||||||||||||||||||||||||||||||||||||
| Switch Port Information | Supported protocols: LLDP, CDP, EDP Displayed information: Link speed, advertised port speeds, PoE (class/watts/volts), port number and name (including SFP slot), port VLAN ID, switch name, switch description (operating system), IP address, MAC address, device capability (switch, bridge, router), link discovery protocol, delay skew by pair Up to 10 unlinked switches can be displayed and selected |
||||||||||||||||||||||||||||||||||||||||
| Target Devices | 10 IPv4 and 10 IPv6 user-definable targets by URL or IP address | ||||||||||||||||||||||||||||||||||||||||
| VLAN Configuration | Set VLAN number and priority for RJ45, SFP and Wi-Fi interface (support for 3 levels) | ||||||||||||||||||||||||||||||||||||||||
| 802.1x Port Security | EAP Method: PEAP, TLS, EAP-TLS Authentication: MSCHAPV2, GTC, PAP. |
||||||||||||||||||||||||||||||||||||||||
| Ping Test IPv4 and IPv6 Copper/Fibre/Wi-Fi |
Ping up to three targets per test (from user list or enter at test time) Ping count: 1 to 999,999 Inter-packet delay: 10 to 5000 ms with a single target, 1000 ns fixed with multiple targets Packet size: 8 to 3000 bytes, 64 bytes fixed with multiple targets Results: Time to test, Pass/Fail, Tx/Rx count, URL-to-IP address resolution, min/avg/max delay time Test progress viewable in real-time |
||||||||||||||||||||||||||||||||||||||||
| TraceRoute Test IPv4 and IPv6 Copper/Fibre/Wi-Fi |
1 target from user list or entered at test time Max number of hops: 2 to 100 Timeout: 2 to 30 seconds Payload: ICMP or UDP DNS lookup: Selectable on/off Results: Time to test, Pass/Fail, URL-to-IP address resolution, host address or name of each hop, response time of each hop (3 tests per hop) |
||||||||||||||||||||||||||||||||||||||||
| Netscan Test Copper/Fibre/Wi-Fi |
Creates a list of active devices on the network Scan range: local subnet, Class C/24, Class C/20, Class B/16 or custom range with start and end IP address |
||||||||||||||||||||||||||||||||||||||||
| Wi-Fi Capabilities | |||||||||||||||||||||||||||||||||||||||||
| Built-in Wi-Fi | Internal radio: Wi-Fi 5, 2.4/5 GHz bands Antennas: Internal and external, user selectable External antenna connector: RP-SMA male |
||||||||||||||||||||||||||||||||||||||||
| External Wi-Fi | Support for Wi-Fi 5/6/6E/7 USB adapters using MediaTek chipsets 2.4/5/6 GHz bands NETGEAR model A9000/BE6500 verified compatible |
||||||||||||||||||||||||||||||||||||||||
| Security Support | Open, WEP, WPA2, WPA3, WPA2-Enterprise, WPA3-Enterprise | ||||||||||||||||||||||||||||||||||||||||
| Wi-Fi Testing & Diagnostics | |||||||||||||||||||||||||||||||||||||||||
| Channel Map | Signal strength, channel number and channel width of detected access points in the 2.4/5/6 GHz bands Channel utilisation and number of devices/clients per channel |
||||||||||||||||||||||||||||||||||||||||
| Channel Details | Channel utilisation histogram (1 min/10 min/1 hour) SSID (name), BSSID (MAC address), signal strength (dBm and %), security mode of all detected access points |
||||||||||||||||||||||||||||||||||||||||
| Access Point Test | Signal strength and data rate histogram (1 min/10 min/1 hr) | ||||||||||||||||||||||||||||||||||||||||
| Access Point Location | Signal strength indicator using internal or external antenna with selectable audible signal level indicator | ||||||||||||||||||||||||||||||||||||||||
| General Information | |||||||||||||||||||||||||||||||||||||||||
| Size & Weight | 107 x 218 x 50 mm, 4.2 x 8.6 x 2.0 inches 772 g, 27.2 oz including battery. |
||||||||||||||||||||||||||||||||||||||||
| Battery | Lithium polymer ternary, 7.4VDC, 7250mAH (53.28 Wh typical) Typical operating time: 10 hours Charge time: up to 8 hours with tester powered off |
||||||||||||||||||||||||||||||||||||||||
| Input Power | 5V/3A DC. USB-C with Power Delivery | ||||||||||||||||||||||||||||||||||||||||
| Display | IPS 5.0-inch capacitive touch screen, 480x854 resolution, LED backlight | ||||||||||||||||||||||||||||||||||||||||
| Input | Touchscreen, USB keyboard, USB mouse | ||||||||||||||||||||||||||||||||||||||||
| CPU | ARM Cortex A72, 4-core, 1.5 GHz 2 GB RAM, 32 GB storage |
||||||||||||||||||||||||||||||||||||||||
| Operating Temperature | -7°C to 55°C (19°F to 131°F), non-condensing Battery will not operate outside of this temperature range |
||||||||||||||||||||||||||||||||||||||||
| Battery Charging Temperature | 0°C to 45°C (32°F to 113°F), non-condensing | ||||||||||||||||||||||||||||||||||||||||
| Storage Temperature | -20°C to 70°C (-4°F to 158°F), non-condensing | ||||||||||||||||||||||||||||||||||||||||
| Test Reporting | On-board PDF reporting saved internally or to USB flash drive Transfer projects to TREND AnyWARE Cloud |
||||||||||||||||||||||||||||||||||||||||
| AnyWARE Cloud Integration | Supports project download and upload to AnyWARE Cloud via Wi-Fi and wired Ethernet connections | ||||||||||||||||||||||||||||||||||||||||