Megger ODEN 400V AT/S/X/H Primary Current Injection Test System - Choice of Control & Current Unit
The Megger ODEN AT primary current injection test system has been specially designed for testing protective relay equipment and circuit breakers. It can also be used to test the turn ratio of current transformers and for other applications that require high variable currents. The ODEN AT can also be set to test circuit breakers with reclosing relays and sectionalisers and is ideal for performing heat runs as the current can be applied continuously or through programmable intervals. It is also capable of testing the integrity of ground grids and safety-ground devices.
The system consists of a control unit with one, two, or three current units. There are three versions of the current unit: S, X, and H. The S and X current units are identical except that the X unit has an additional 30/60 V output. The H unit is rated for an even higher current. These current units make it possible to configure the ODEN AT system for a range of different tests.
High current output - ODEN AT systems for 400 V, 50 Hz
The control unit has many advanced features, such as a powerful measurement section that can display turn ratio as well as time, voltage, and current. A second measurement channel can also be used to test an additional current or voltage. The ODEN AT can calculate the current transformer turns ratio, impedance, resistance, power, power factor/tan delta, and phase angle.
The current and voltage can be presented as percentages of nominal value. It also has a fast-acting hold function that freezes short-duration readings on the digital display, so when the voltage or contact signal arrives at the 'stop' input, the object under test interrupts the current, or the injection is stopped.
All parts are portable, and the ODEN AT can be quickly assembled and connected. An ODEN AT system consists of a control unit and one, two, or three current units. There are three different versions of the current units: S-unit (standard), X-unit (extra 30/60 V outlet), and H-unit (high current). The system designation indicates the number and version of current units included.
Key Features
- Display
- Miniature circuit breaker used for current output
- Current reduction button
- Fine adjustment knob
- Indicator lamps
- Input for voltmeter
- Input for ammeter 2
- Hold function
- Selection/setting (CHANGE) knob
- Setting buttons
- Injection
- Momentary Injection
- Red warning lamp
- Manual shut-off
- Automatic injection stop
- Stop-condition indicator
- Status indicator
- Stop input
- USB port
What's Included?
- 0.7-metre ground cable
- 0.22-metre ground cable
- 5-metre ground cable
- Cable set
- 5-metre 240 V mains voltage cable
5-metre ground cable
5-metre 240 V mains voltage cable
0.7-metre ground cable
0.22-metre ground cable
Cable set
Product Range
- Megger BH-44020 ODEN AT 400C 400 V Control Unit
- Megger BH-54010 ODEN 400S 400 V Standard Current Unit
- Megger BH-54020 ODEN 400X 400 V Current Unit Extra Winding
- Megger BH-54030 ODEN 400H 400 V High Current Unit
- Megger BH-64011 ODEN AT/1S 400 V 1 Control Unit, 1 S Current Unit
- Megger BH-64012 ODEN AT/2S 400 V 1 Control Unit, 2 S Current Units
- Megger BH-64013 ODEN AT/3S 400 V 1 Control Unit, 3 S Current Units
- Megger BH-64021 ODEN AT/1X 400 V 1 Control Unit, 1 X Current Unit
- Megger BH-64022 ODEN AT/2X 400 V 1 Control Unit, 2 X Current Units
- Megger BH-64023 ODEN AT/3X 400 V 1 Control Unit, 3 X Current Units
- Megger BH-64031 ODEN AT/1H 400 V 1 Control Unit, 1 H Current Unit
- Megger BH-64032 ODEN AT/2H 400 V 1 Control Unit, 2 H Current Units
- Megger BH-64033 ODEN AT/3H 400 V 1 Control Unit, 3 H Current Units
Datasheets
| SPECIFICATIONS ODEN AT | ||
|---|---|---|
| Specifications are valid at nominal input voltage and an ambient temperature of +25°C, (77°F). Specifications are subject to change without notice. | ||
| Environment | Application Field | The instrument is intended for use in high-voltage substations and industrial environments |
| Operating Temperature | 0°C to +50°C (+32°F to +122°F) | |
| Storage & Transport Temperature | -25°C to +55°C (-13°F to +127°F) | |
| Humidity | 5% - 95% RH, non-condensing | |
| CE-Marking | LVD | 2014/35/EU |
| EMC | 2014/30/EU | |
| RoHS | 2011/65/EU | |
| General | Mains Voltage | 400 V AC, 50 / 60 Hz |
| Mains Inlet | IEC 60309-2, 63 A | |
| Input Current | Output current x open circuit voltage / input voltage | |
| Protection | The output transformer has a built-in thermal cut-out, and a miniature circuit breaker protects the primary side | |
| Control Unit AT Dimensions | 570 x 310 x 230 mm (22.4” x 12.2” x 9”) | |
| Current Unit S, X H Dimensions | 570 x 310 x 155 mm (22.4” x 12.2” x 6”) | |
| Dimensions Complete with Cart | 690 x 350 x 860 mm (27.2” x 13.8” x 33.9”) | |
| Control Unit AT Weight | 25 kg (55 lbs) | |
| Current Unit S Weight | 42 kg (92.6 lbs) | |
| Current Unit X Weight | 45 kg (99.3 lbs) | |
| Current Unit H Weight | 49 kg (108 lbs) | |
| Cart Weight | 11 kg (24.3 lbs) | |
| Display | LCD | |
| Available Languages | English, German, French, Spanish, Swedish | |
| Measurement Section | Ammeter 1 Measurement method | AC, true RMS (or DC if the function is activated) |
| Ammeter 1 Inaccuracy | 1% of range ±1 digit | |
| Ammeter 1 Ranges | Current unit S, 0 - 4800 A / 0 - 15 kA Current unit H, 0 - 9600 A / 0 - 30 Current unit X, 0 - 960 A / 0 - 3 kA The above is valid for one current unit or units in parallel. |
|
| Ammeter 2 Ranges | 0 - 2.000 A / 0 - 20.00 A | |
| Voltmeter Measurement Method | AC, true RMS (or DC if activated) | |
| Voltmeter Ranges | 0 - 9.999 V 10.00 - 99.99 V 100.0 - 200.0 V |
|
| Voltmeter Inaccuracy | 1% of range ±1 digit | |
| Voltmeter Input Resistance (Rin) | 240 kΩ (range 0 - 200 V) 24 kΩ (other ranges) |
|
| Voltmeter Dielectric Withstand | 2.5 kV | |
| Timer Presentation | In seconds, mains frequency cycles or hours and minutes | |
| Timer Ranges | 0.000 - 999.9 s 0 - 9999 cycles 0.001 s - 99 h 59 min |
|
| Timer Inaccuracy | ±(1 digit + 0.01% of value) For the stop condition in INT-mode, 1 ms shall be added to the specified measurement error |
|
| Stop Input Max. Input Voltage | 250 V AC / 275 V DC | |
| Phase Angle Range | 0 - 359º | |
| Phase Angle Resolution | 1º | |
| Phase Angle Inaccuracy | ±2º (for voltage and current readings that are higher than 10% of the selected range) | |
| Z, P, R, X, S, Q and Power Factor (cos φ) | For these measurements, the result is calculated using U, I, and sometimes φ | |
| Imax | Stores the highest current value that exists ≥100 ms | |
| INT-level | Threshold indicating that current is interrupted. It can be set to 0.7% or 2.1% of the Ammeter 1 range | |
| SKU | ODEN400-AT/S/X/H |
|---|
