Radiodetection Super C.A.T4+ T1 Transmitter - Choice of Frequencies
The Radiodetection's SuperCAT4+ is compatible with all T1 Transmitters. Higher frequency transmitters are recommended for high-impedance cables. Lower-frequency signals travel further on lower-impedance services. Designed to meet the demanding environments of the construction industry, this multi-utility locator can be used with a wide range of sondes and accessories.
SuperCAT4+ can be used to locate a comprehensive set of active frequencies to support the detection and tracing of different cable types in varied environmental conditions.
The audio signals emitted by the SuperCAT4+ are derived from the signals detected. Radio, Power, and Active signals can be easily distinguished from each other, and background noise helps identification of target utilities, and aids the differentiation of closely co-located utilities.
High levels of electrical interference, as found around substations and near high-voltage transmission cables can overload sensitive electronics. Dynamic Overload Protection filters this interference out, enabling SuperCAT4+ to continue locating where other units struggle.
Key Features
- Safety Built-In
- Dig more safely with StrikeAlert
- Real Sound
- TRUDEPTH
- Dynamic Overload Protection
- Signal Clamping
Product Range
- RD 10/T1-SUPERCAT4+131 SuperC.A.T4+ T1-131 Transmitter, with frequencies 131kHz, 8kHz, 33kHz
- RD 10/T1-SUPERCAT4+640 SuperC.A.T4+ T1-640 Transmitter, with frequencies 640Hz, 8kHz, 33kHz
- RD 10/T1-SUPERCAT4+640/65 SuperC.A.T4+ T1-640/65 Transmitter, with frequencies 640Hz, 8kHz, 65kHz
Safety Built-In
All SuperCAT4+ models come with a range of features designed to aid safe working practices.
Dig more safely with StrikeAlert™
StrikeAlert warns the user of the possible presence of shallow cables and utility lines in both Power and Active Line modes.
Although work practices and guidelines insist power cables are buried below a certain depth, a common cause of cable strikes is unexpectedly shallow cables.
Real Sound
The audio signals emitted by the SuperCAT4+ are derived from the signals detected. Radio, Power, and Active signals can be easily distinguished from each other, and background noise helps identification of target utilities, and aids the differentiation of closely co-located utilities.
Dynamic Overload Protection
High levels of electrical interference, as found around substations and near high-voltage transmission cables can overload sensitive electronics. Dynamic Overload Protection filters this interference out, enabling SuperCAT4+ to continue locating where other units struggle.
TRUDEPTH™
Indicates depth when the locator is oriented correctly above the target cable, pipe, or sonde for the most accurate reading.
Brochures & Catalogues
| SuperCAT4+ | |||||
|---|---|---|---|---|---|
| StrikeAlert | ✔ | ||||
| Depth readout* | ✔ | ||||
| Dynamic Overload Protection | ✔ | ||||
| Passive Modes | |||||
| Radio Mode | ✔ | ||||
| Power Mode 50Hz/60Hz** | ✔ | ||||
| Sondes | |||||
| Sonde 512/640Hz** | ✔ | ||||
| Sonde 33kHz | ✔ | ||||
| Active locating using | T1-512 | T1-512/65 | T1-131 | ||
| T1-640 | T1-640/65 | ||||
| Direct Connection | |||||
| Sonde 512/640Hz** | ✔ | ✔ | ✘ | ||
| Sonde 8kHz | ✔ | ✔ | ✔ | ||
| 33kHz | ✔ | ✘ | ✔ | ||
| 65kHz | ✘ | ✔ | ✘ | ||
| Super HF 131kHz | ✘ | ✘ | ✔ | ||
| Induction | |||||
| Sonde 8kHz | ✔ | ✔ | ✔ | ||
| 33kHz | ✔ | ✘ | ✔ | ||
| 65kHz | ✘ | ✔ | ✘ | ||
- * Choose between M (Metric) or I (Imperial) locator models
- ** Power frequency and corresponding active low frequency set by the model, (50Hz - 640Hz and 60Hz - 512Hz)
| SKU | 10/T1-SUPERCAT4+ |
|---|
