Important Notice
This item is made-to-order exclusively for you once your order is placed. As a result, it is not eligible for cancellation or return under our standard policy. Your statutory rights remain unaffected.
Siglent SPS6000X Series Single Channel Programmable DC Switching Power Supply
- Rated Voltage: 200 V or 100 V
- Rated Current: 25 A or 50 A
- Rated power: 1500 W
- OVP, OCP, LPP, OTP protection
SKU
SPS6000X
The SPS6000X Series has two models, SPS6225X and SPS6150X, with rated output voltages and currents of 200 V / 25 A and 100 V / 50 A, respectively, with a peak output power of 1500 W. To accommodate varying requirements, users can connect up to five identical SPS6000X chassis in parallel to enhance the total output power.
The models have a high-clarity 3.12-inch OLED display, an intuitive user interface that simplifies, and a minimum resolution of 10 mV / 10 mA. They also incorporate adjustable rise times for output voltage and current, list sequence programming, and built-in safety measures, including overvoltage, overcurrent, power limit, and overtemperature protections, safeguard devices under test (DUT) and the power supply itself.
The SPS6000X constant power mode dynamically adjusts the voltage and current ranges to maintain peak output. While the customisable rise and fall slew rates minimise inrush current risks. The discharge circuit ensures residual voltage on output terminals is safely dissipated after power-off, preventing potential hazards.
Remote control and monitoring through LAN, USB, and an optional USB-GPIB module. Analogue control for voltage or current adjustments via a 0-10 V signal and output monitoring terminals for real-time display of current or voltage changes through connected measurement instruments.
Parallel connections of up to five units achieve high power density and scalability. The negative terminals can float or connect to the chassis ground. Overcurrent, overvoltage, and overtemperature modes include visual alerts and user-friendly reset mechanisms.
Key Features
- Rated Voltage: 200 V / 100 V
- Rated Current: 25 A / 50 A
- Rated power: 1500 W
- Wide range of output voltage and current values in a high-efficiency power supply
- CV, CC priority mode selection, better protection of equipment under test
- Load transient recovery time (Load change from 50~100%) < 2.5 ms
- Adjustable voltage and current slew rates
- Setting and readback resolution: 10 mV, 10 mA
- User-enabled internal output discharge circuit to accelerate output voltage reduction
- Remote Sense function to decrease lead resistance error
- Local list function with up to 50 steps, USB import list sequence file
- External analogue voltage control. Voltage and current monitoring outputs
- OVP, OCP, LPP, OTP protection
- 3.12-inch OLED high-brightness display with a wide viewing angle of 170 degrees
- Equipped with USB, LAN standard communication interface, optional USB GPIB module
- 44 mm (1U) height, 19” width for convenient rack mounting
- Embedded Web Server offers remote control through a web browser without the need for drivers or additional software
What's Included?
- Choice of Power Supply
- Quick Start
- Power Cord
- USB Cable
- Output Guard
- Calibration Certificate
Product Range
- Siglent SPS6150X Single Channel Programmable DC Switching Power Supply, 1U, 100V/50A/1500W
- Siglent SPS6225X Single Channel Programmable DC Switching Power Supply, 1U, 200V/25A/1500W
Offers
Free Insulated Screwdrivers
- CK Tools T4897 C.K VDE Precision Screwdriver Set - T4897, typically £27.35
Technical Information
Specification
| SPS6225X | SPS6150X | |
|---|---|---|
| Rated Output Voltage | 200 V | 100 V |
| Rated Output Current | 25 A | 50 A |
| Total Rated Output Power | 1500 W | |
| Power Ratio | 3.33 | |
| C.V Mode | ||
| Line Regulation | 40 mV (From 90 ~ 132 Vac or 170 ~ 265 Vac, constant load) | 5 mV (From 90 ~ 132 Vac or 170 ~ 265 Vac, constant load) |
| Load Regulation | 100 mV (From no load to full load, constant input voltage) | 50 mV (From no load to full load, constant input voltage) |
| Ripple and Noise *1 | Noise bandwidth 20 MHz; Ripple bandwidth 5 Hz ~1 MHz | |
| RIPPLE (pk to pk)@220 Vac Input | 220 mV | 120 mV |
| RMS RIPPLE@220 Vac Input | 39 mV | 30 mV |
| Voltage Programming Accuracy *2 | 0.1% ± 10 mV | |
| Voltage Programming Resolution | 10 mV | |
| Voltage Readback Accuracy *2 | 0.1% ± 20 mV | |
| Voltage Readback Resolution | 10 mV | |
| Temperature Coefficient | 100 ppm/°C from rated output voltage following a 30-minute warm-up | |
| Remote Compensation Voltage (Single Wire) | 0.6 V | |
| Rise Time | 10% ~ 90% of rated output voltage, rated resistance load | |
| Rise Time Rated Load: | 30 ms | |
| Rise Time No Load: | 30 ms | |
| Fall Time | 90% ~ 10% of rated output voltage, rated resistance load | |
| Fall Time Rated Load | 15 ms | |
| Output Capacitance | 1100 uF | 1760 uF |
| Transient Response Time | 2.5 ms (Time for recovery to within 0.5% of its rated output after the transient from 10% to 90% of the rated output power) | |
| C.C Mode | ||
| Line Regulation | 40 mA (From 90 ~ 132Vac or 170 ~ 265Vac,constant load) | 30 mA (From 90 ~ 132Vac or 170 ~ 265Vac,constant load) |
| Load Regulation | 40 mA (From No load to Full load, constant input voltage) | 50 mA (From No load to Full load, constant input voltage) |
| r.m.s *3 | 30 mA | 40 mA |
| Current Setting Accuracy | 0.2% ± 30 mA | |
| Current Programming Resolution | 10 mA | |
| Current Readback Accuracy | 0.2% ± 40 mA | |
| Current Readback Resolution | 10 mA | |
| Temperature Coefficient | 200 ppm/°C from rated output current following a 30-minute warm-up. | |
| Protection Function | ||
| OVP Setting Range | 20 V ~ 220 V | 10 V ~ 110 V |
| OVP Setting Accuracy | ± (2% of rated output voltage) | |
| OCP Setting Range | 2.5 A ~ 25 A | 5.0 A ~ 55 A |
| OCP Setting Accuracy | ± (2% of rated output current) | |
| OTP | Over temperature alarm and shut off output. | |
| Low AC Input Protection | Shut off output. | |
| LPP | The overpower limit is approximately 102% of the rated output power. | |
| Rising/Falling Voltage Slew Rate Only applicable if V I Mode is set to CV Slew Rate Priority |
0.001 ~ 4 V/ms | 0.001 ~ 2 V/ms |
| Rising/Falling Current Slew Rate Only applicable if V I Mode is set to CC Slew Rate Priority |
0.001~0.5 A/ms | 0.001 ~ 1.0 A/ms |
| Efficiency@220 Vac Input Full Power and Full Current Output | >86% | |
| Efficiency@220 Vac Input Full Power and Full Current Output | >90% | |
| Parallel capability | 5 Units | |
| Series capability *4 | The output voltage should not exceed 400 V when the series connects the same rated current products | |
| Analogue Programming and Monitoring | ||
| External Voltage Control of the Voltage Output | Accuracy: +0.5% of rated output voltage | |
| External Voltage Control of the Current Output | Accuracy: +1% of rated output current | |
| Output Voltage/Current Monitor Accuracy | ±1% | |
| Shutdown Control | Close output with LOW (0 V~0.5 V) or short circuit | |
| Output On/Off Control | Use LOW (0 V~0.5 V) or hang to turn off the output Use HIGH (4.5 V~5 V) to turn on the output |
|
| CV/CC/ERR/ ON/OFF Status |
Photo coupler open collector output Maximum voltage 30 V, maximum sink current 8 mA |
|
| Input Characteristics | ||
| Normal Rated Input | 100 Vac ~ 240 Vac, 50 Hz ~ 60 Hz, Single phase | |
| Input Voltage Range | 90 Vac ~ 265 Vac | |
| Input Frequency Range | 47 Hz ~ 63 Hz | |
| Input Fuse (Built-in) | T30 (6 X 32 mm) | |
| Maximum Input Current | ||
| 90Vac | ≈23.1 A | |
| Surge Current | < 30 A | |
| Maximum Input Power | 2100 VA | |
| Power Factor | ||
| 90 Vac | 0.99 | |
| 220 Vac | 0.98 | |
| Communications Interfaces | ||
| USB | Type A: HOST, Type B: DEVICE, SPEED: 1.1/2.0 | |
| LAN | MAC address, Gateway IP address, Instrument IP address, Subnet Mask | |
| GPIB | Optional: USB-GPIB adapter | |
| Environment Conditions | ||
| Operating Temperature | 0˚C ~ 50˚C | |
| Storage Temperature | -25˚C ~ 70˚C | |
| Operating Humidity | 20% ~ 85% RH; No condensation | |
| Storage Humidity | 90% RH or less; No condensation | |
| Altitude | ≤ 2000 m | |
| General | ||
| Weight (host only) | 10 kg | |
| Dimensions (WxHxD) | 483 mm x 44 mm x 468 mm | |
| Cooling | Internal fan-forced air cooling | |
| Safety Standard | EN60950, EN61326, EN55022 Grade B/Class B | |
| Withstand Voltage | Input to Base: 2500 VAC for 1 minute without abnormality Input to Output: 2500 VAC for 1 minute without abnormality Output to Base: 400 VDC for 1 minute without abnormality |
|
| Insulation Resistance | Input to Base: 500 VDC, ≥100 mΩ Input and Output: 500 VDC, ≥ 100 mΩ Output to Base: 500 VDC, ≥100 mΩ |
|
| *1: Use a probe to measure the positive and negative poles of the sense terminal, the bandwidth limit is 20 MHz *2: %output+offset, when the output voltage is less than 5 V, the offset is 200 mV *3: The bandwidth limit measured by the current probe is 1 MHz *4: The connection of multiple machines is subject to the connection restrictions between machines in the user's manual |
||
Document Downloads
Additional Information
SKU
SPS6000X
Siglent SPS6000X Series Single Channel Programmable DC Switching Power Supply
£1,780.00
£2,136.00 inc vat
£1,780.00
£2,136.00 inc vat
